Cara membuat Konfigurasi EIGRP IPv4
1. Buat Skema jaringan terlebih dahulu
Skema Jaringan EIGRP
2. Konfigurasi Router
Router 1
Router>enable
Router#conf
ter
Enter
configuration commands, one per line. End with CNTL/Z.
Router(config)#int
fa0/0
Router(config-if)#ip
add 192.168.1.1 255.255.255.0
Router(config-if)#no
shut
Router(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#int
se2/0
Router(config-if)#ip
add 10.0.0.1 255.0.0.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial2/0, changed state to down
Router(config-if)#no
shut
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to
up
Router>en
Router#conf
t
Enter
configuration commands, one per line. End with CNTL/Z.
Router(config)#router
eigrp
% Incomplete
command.
Router(config)#router
eigrp 1
Router(config-router)#network
10.0.0.0
Router(config-router)#network
192.168.1.0
Router(config-router)#exit
Router(config)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 10.0.0.2 (Serial2/0) is up: new
adjacency
Router 2
Router>enable
Router#conf
t
Enter
configuration commands, one per line. End with CNTL/Z.
Router(config)#int
fa0/0
Router(config-if)#ip
add 192.168.2.1 255.255.255.0
Router(config-if)#no
shut
Router(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int
se2/0
Router(config-if)#ip
add 10.0.0.2 255.0.0.0
Router(config-if)#no
shut
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
Router(config-if)#exit
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
Router(config)#exit
Router#
%SYS-5-CONFIG_I:
Configured from console by console
Router#conf
t
Enter
configuration commands, one per line. End with CNTL/Z.
Router(config)#int
se3/0
Router(config-if)#ip
% Incomplete
command.
Router(config-if)#ip
Router(config-if)#int
se3/0
Router(config-if)#ip
% Incomplete
command.
Router(config-if)#ip
add 20.0.0.2 255.0.0.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial3/0, changed state to down
Router(config-if)#no
shut
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED:
Interface Serial3/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial3/0, changed state to up
Router(config)#router
eigrp 1
Router(config-router)#network
10.0.0.0
Router(config-router)#
%DUAL-5-NBRCHANGE:
IP-EIGRP 1: Neighbor 10.0.0.1 (Serial2/0) is up: new adjacency
Router(config-router)#network
192.168.2.0
Router(config-router)#network
20.0.0.0
Router(config-router)#exit
Router(config)#
%DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 20.0.0.1 (Serial3/0) is up: new
adjacency
Router 3
Router>en
Router#conf
t
Enter
configuration commands, one per line. End with CNTL/Z.
Router(config)#int
fa0/0
Router(config-if)#ip
add 192.168.3.1 255.255.255.0
Router(config-if)#no
shut
Router(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#aint
se2/0
^
% Invalid
input detected at '^' marker.
Router(config-if)#int
se2/0
Router(config-if)#ip
add 20.0.0.1 255.0.0.0
Router(config-if)#no
shut
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
Router(config)#router
eigrp 1
Router(config-router)#network
20.0.0.0
Router(config-router)#
%DUAL-5-NBRCHANGE:
IP-EIGRP 1: Neighbor 20.0.0.2 (Serial2/0) is up: new adjacency
Router(config-router)#network
192.168.3.0
Router(config-router)#exit
Setelah semua router di konfigurasi, cek jaringannya apakah sudah saling terhubung dengan sesama jaringannya
Tidak ada komentar:
Posting Komentar